“The foundation of your home is built up by the walls. The weather out there won’t be good for the exterior walls of your house. If you want your wall to be waterproof, you have to paint it. After dealing with rain, snow, wind, dust, and the heat of the outside environment, the paint will begin to peel off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
A lot of dust and dirt is carried by air and sticks onto the outer part of your home. To ensure the efficiency of the process, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. Then use a power washer to wash it off.
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop over time on your walls. Follow up the cleaning process with a thorough look at the cracks and holes on the wall to make sure proper weatherproofing is ensured. You can fill them with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
The mixture of cement penetrated inside the cracks and seals them. Remove all the loose cement from the wall before applying the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make sure your wall is waterproof, you need to apply the cement waterproofener. After applying the cement in the crevices, let it dry and then apply the waterproof paint seal for the exterior walls. Allow it to become wet after that.
Step 5: Pick the right water-proofer
There are a lot of waterproof products in the market. You have to pick the right one for the wall. The water-proofer should be chosen based on whether it is a concrete wall or a silicate-based one.
You can choose between a silicate-based concrete sealer and a concrete coating. You can add strength to your walls with a plaster waterproof Additive.
Step 6: Apply the water-proofer
You can apply the water-proofer with a roller or brush. Give a thin coat if you want to apply more than one layer. Allow the first coating to dry before adding the second one.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layers, you need to use a tar-based pitch after drying the cement. You can apply it on the exterior wall.
After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your Walls.
Step 8: Consider adding gravel
To lay the drainage pipes, you need a base below the footer. The drainage pipes will get adequate support from a gravel base. Gravel is long-lasting and provides better protection.
You need to lay the drainage pipe-cover along with the gravel. Next to the footer, level the position of the gravel and back-fill it. Make sure there is at least 3 inches of coverage over the pipe.
Step 9: Add a fabric barrier
Attach the pipe with a fabric barrier. Ensuring a fabric barrier is going to keep your system free of dirt. Simply back-fill the trench and build the top of the dirt relatively high and allow it to settle for some time. Slope the ground away from the walls for the run-off after youTrademarkia.
Conclusion:
“Your home gets a new life and strength when it’s waterproof. If you want good waterproof solutions for your walls, Magicrete is here to help you. At a very low and affordable price, Magi Crete has quality service and proper weatherproofing.”
